EC150 CO2/H2O Open-Path Gas Analyzer
Innovative Design
Use as part of open-path eddy-covariance systems or as a stand-alone IRGA
weather aplicaciones soportadas water aplicaciones soportadas energy aplicaciones soportadas gas flux and turbulence aplicaciones soportadas infrastructure aplicaciones soportadas soil aplicaciones soportadas

Overview

Campbell Scientific’s EC150 is an open-path analyzer specifically designed for eddy-covariance flux measurements. As a stand-alone analyzer, it simultaneously measures absolute carbon-dioxide and water-vapor densities, air temperature, and barometric pressure. With the optional CSAT3A sonic anemometer head, the EC150 also measures three-dimensional wind speed and sonic air temperature.

Read More

Benefits and Features

  • New conformal coating helps protect sonic transducers in corrosive environments
  • Unique optical configuration gives a slim aerodynamic shape with minimal wind distortion
  • Analyzer and sonic anemometer measurements are synchronized by a common set of electronics
  • Maximum output rate of 60 Hz with 20 Hz bandwidth
  • Low power consumption; suitable for solar power applications
  • Low noise
  • Measurements are temperature compensated without active heat control
  • Angled windows to shed water and are tolerant to window contamination
  • Field rugged
  • Field serviceable
  • Factory calibrated over wide range of CO2, H2O, pressure, and temperature in all combinations encountered in practice
  • Extensive set of diagnostic parameters
  • Fully compatible with Campbell Scientific dataloggers; field setup, configuration, and field zero and span can be accomplished directly from the datalogger
  • Speed of sound determined from three acoustic paths; corrected for crosswind effects
  • Innovative signal processing and transducer wicks considerably improve performance of the anemometer during precipitation events

Images

Detailed Description

The CSAT3A has the following outputs:

  • Ux (m/s)*
  • Uy (m/s)*
  • Uz (m/s)*
  • Sonic Temperature (°C)*
  • Sonic Diagnostic*

The EC150 has the following outputs:

  • CO2 Density (mg/m3)
  • H2O Density (g/m3)
  • Gas Analyzer Diagnostic
  • Ambient Temperature (°C)
  • Atmospheric Pressure (kPa)
  • CO2 Signal Strength
  • H2O Signal Strength
  • Source Temperature (°C)

*The first five outputs require the CSAT3A Sonic Anemometer Head.

Specifications

Operating Temperature Range -30° to +50°C
Calibrated Pressure Range 70 to 106 kPa
Power 5 W (steady state and power up) at 25⁰C
Measurement Rate 60 Hz
Output Bandwidth 5, 10, 12.5, or 20 Hz (user-programmable)
Output Options SDM, RS-485, USB, analog (CO2 and H2O only)
Auxiliary Inputs Air temperature and pressure
Gas Analyzer/Sonic Volume Separation 5.0 cm (2.0 in.)
Warranty 3 years or 17,500 hours of operation (whichever comes first)
Cable Length 3 m (10 ft) from EC150 and CSAT3A to EC100
Weight
  • 2.0 kg (4.4 lb) for EC150 head and cables
  • 1.7 kg (3.7 lb) for CSAT3A head and cables
  • 3.2 kg (7.1 lb) for EC100 electronics

Gas Analyzer
Path Length 15.37 cm (6.05 in.)
A temperature of 20°C and pressure of 101.325 kPa was used to convert mass density to concentration.

Gas Analyzer - CO2 Performance
-NOTE- A temperature of 20°C and pressure of 101.325 kPa was used to convert mass density to concentration.
Accuracy
  • Assumes the following: the gas analyzer was properly zero and spanned using the appropriate standards; CO2 span concentration was 400 ppm; H2O span dewpoint was at 12°C (16.7 ppt); zero/span temperature was 25°C; zero/span pressure was 84 kPa; subsequent measurements made at or near the span concentration; temperature is not more than ±6°C from the zero/span temperature; and ambient temperature is within the gas analyzer operating temperature range.
  • 1% (standard deviation of calibration residuals)
Precision RMS (maximum) 0.2 mg/m3 (0.15 µmol/mol)

Nominal conditions for precision verification test: 25°C, 86 kPa, 400 μmol/mol CO2, 12°C dewpoint, and 20 Hz bandwidth.
Calibrated Range 0 to 1,000 μmol/mol (0 to 3,000 µmol/mole available upon request.)
Zero Drift with Temperature (maximum) ±0.55 mg/m3/°C (±0.3 μmol/mol/°C)
Gain Drift with Temperature (maximum) ±0.1% of reading/°C
Cross Sensitivity (maximum) ±1.1 x 10-4 mol CO2 /mol H2O

Gas Analyzer - H2O Performance
-NOTE- A temperature of 20°C and pressure of 101.325 kPa was used to convert mass density to concentration.
Accuracy
  • Assumes the following: the gas analyzer was properly zero and spanned using the appropriate standards; CO2 span concentration was 400 ppm; H2O span dewpoint was at 12°C (16.7 ppt); zero/span temperature was 25°C; zero/span pressure was 84 kPa; subsequent measurements made at or near the span concentration; temperature is not more than ±6°C from the zero/span temperature; and ambient temperature is within the gas analyzer operating temperature range.
  • 2% (standard deviation of calibration residuals)
Precision RMS (maximum) 0.004 g/m3 mmol/mol (0.006 mmol/mol)

Nominal conditions for precision verification test: 25°C, 86 kPa, 400 μmol/mol CO2, 12°C dewpoint, and 20 Hz bandwidth.
Calibrated Range 0 to 72 mmol/mol (38°C dewpoint)
Zero Drift with Temperature (maximum) ±0.037 g/m3/°C (±0.05 mmol/mol/°C)
Gain Drift with Temperature (maximum) ±0.3% of reading/°C
Cross Sensitivity (maximum) ±0.1 mol H2O/mol CO2

Sonic Anemometer - Accuracy
Offset Error
  • < ±8.0 cm s-1 (for ux, uy)
  • < ±4.0 cm s-1 (for uz)
  • ±0.7° while horizontal wind at 1 m s-1 (for wind direction)
Gain Error
  • < ±2% of reading (for wind vector within ±5° of horizontal)
  • < ±3% of reading (for wind vector within ±10° of horizontal)
  • < ±6% of reading (for wind vector within ±20° of horizontal)
Measurement Precision RMS
  • 1 mm s-1 (for ux, uy)
  • 0.5 mm s-1 (for uz)
  • 0.025°C (for sonic temperature)
  • 0.6° (for wind direction)
Speed of Sound Determined from 3 acoustic paths (corrected for crosswind effects)
Rain Innovative ultrasonic signal processing and user-installable wicks considerably improve the performance of the anemometer under all rain events.

Ambient Temperature
Manufacturer BetaTherm 100K6A1IA
Total Accuracy ±0.15°C (-30°C to +50°C)

Compatibility

Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.

Dataloggers

Product Compatible Note
CR1000 (retired)
CR1000X
CR300
CR3000 (retired)
CR310
CR350
CR6
CR800 (retired)
CR850 (retired)

Downloads

ECMon v.1.6 (10.7 MB) 29-03-2016

EC100-Series Support Software.

EC100 OS v.8.02 (560 KB) 14-10-2019

EC100 Operating System.

Watch the Video Tutorial: Updating the EC100 Operating System.

View Update History

Device Configuration Utility v.2.31 (47.0 MB) 18-12-2024

A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.

Supported Operating Systems:

Windows 11 or 10 (Both 32 and 64 bit)

View Update History

CSAT3H Heater Controller v.14.2 (46 KB) 02-02-2021

The CSAT3H Heater Controller ships with this encrypted program. This program is for the unlikely event that the program needs to be re-installed or updated to a newer version. Please contact Campbell Scientific if you have questions about the program or would like the algorithm modified for a specific application.

CSAT3H Heater Controller v.14.2 (46 KB) 02-02-2021

The CSAT3H Heater Controller ships with this encrypted program. This program is for the unlikely event that the program needs to be re-installed or updated to a newer version. Please contact Campbell Scientific if you have questions about the program or would like the algorithm modified for a specific application.

EasyFlux DL for CR1000XOP v.2.01 (98.2 KB) 21-07-2022

CR1000X datalogger program for Campbell open-path eddy-covariance systems.

View Update History

Frequently Asked Questions

Number of FAQs related to EC150: 4

Expand AllCollapse All

  1. Which countries can the molecular sieve be shipped to?

    The molecular sieve is a non-hazardous material that can be shipped to any country.

  2. Why did Campbell Scientific start using molecular sieve? Does it have the same effect as the previously used chemicals?

    The molecular sieve has been demonstrated here by our engineering department to be effective at removing CO2 and H2O from the air sample. The change was made for two reasons:

    1. It was a safer alternative than using the previous chemicals.
    2. Increased shipping regulations for the chemicals limited the number of suppliers. 
  3. Can molecular sieve be used in the future to replace bottles for gas analyzers sold before July 2017?

    The molecular sieve is a direct replacement for the old magnesium perchlorate bottles. The molecular sieve may be used for any Campbell Scientific analyzer that used the old bottles.

  4. To prepare the molecular sieve, how many grams are needed per bottle?

    The bottles of sieve for drop-in replacement contain the pellets and a membrane on top. The membrane is necessary to keep the pellets contained while allowing gas to pass over the zeolite. The bottle has the same footprint as the old magnesium perchlorate bottles. The amount in each bottle is listed on the bottle. The amount of sieve needed for each analyzer is the following:

    • The EC150 needs 22 g (drop-in bottle).
    • The IRGASON® needs 22 g (drop-in bottle).
    • The EC155 needs 22 g (drop-in bottle).
    • The AP200 needs 500 g (refill).
    • The 27423 needs 1000 g (refill).
    • The 31022 needs 500 g (refill).
Visit the FAQ Library