AP200 CO2/H2O Atmospheric Profile System
Complete, Integrated System
Preprogrammed and low power
weather aplicaciones soportadas water aplicaciones soportadas energy aplicaciones soportadas gas flux and turbulence aplicaciones soportadas infrastructure aplicaciones soportadas soil aplicaciones soportadas

Overview

The AP200 is a complete, integrated CO2 and H2O atmospheric profile system. It measures carbon dioxide (CO2) and water vapor (H2O) concentration from up to eight intakes, which are normally spaced along the height of a tower to give a vertical profile. The AP200 is often used in conjunction with an eddy-covariance system to measure the storage term and give a more complete measure of the surface gas exchange.

Read More

Benefits and Features

  • Fully integrated system
  • Requires only 13 W (average at 25°C and 12 Vdc)
  • Contains a Campbell Scientific CR1000X Measurement and Control Datalogger
  • Automatically performs CO2 zero and span
  • Automated temperature and pressure control
  • Data logger program included

Images

<dl><dt>Typical AP200 Installation</dt> <dd>1-27693 Heated Sample Intake Assemblies (from 4 up to 8)</dd> <dd>2-9922 20 AWG Power Cable</dd> <dd>3-28547 AP200 System Enclosure</dd> <dd>4-15702 Tubing</dd> <dd>5-Zero/Span Tanks and Regulators (not included)</dd> <dd>6-Instrument Tower (sold separately)</dd></dl>

Detailed Description

Measurements

Primary:

  • CO2 concentration at each intake
  • H2O concentration at each intake
  • System diagnostic word

Secondary:

  • Sample flow rate
  • Sample cell pressure
  • Sample cell temperature
  • Other control variables

Note: Contact the Micromet Group at Campbell Scientific for questions or updates regarding the datalogger program.

Specifications

System Enclosure
Operating Temperature -30° to +45°C
Power Requirements
  • 10 to 16 Vdc (voltage)
  • 13 W (average power at 25°C)
    Average power varies from 12.5 W above +35°C to 22.5 W at -30°C.
  • 3.75 A (45 W) maximum power (cold startup)
Dimensions 52.1 x 44.5 x 29.7 cm (20.5 x 17.5 x 11.7 in.)
Weight
  • 15.9 kg (35 lb) for AP200 base model
  • 1 kg (2.3 lb) for LI-850
  • 272 g (10 oz) for CR1000KD
  • 154 g (5.4 oz) for CFM100/NL116

Pump Module
Pump Type Dual-head diaphragm pump with a brushless dc motor
Mounting Mounted in an insulated, temperature-controlled box inside system enclosure
Control Pumping speed is automatically controlled to maintain the pump inlet pressure at the set point
Maximum Pumping Speed 9.0 liters per minute (LPM)
Pressure Sensor Range 15.0 to 115.0 kPa
Heater 8.0 W (turns on/off at 2°C)
Warm-up Time ~50 min (from -30° to +2°C)
Fan 0.7 W (turns on at 50°C and off at 45°C)

Valve Manifold
Mounting Mounted inside system enclosure
Inlets Eight air sample inlets plus one inlet for zero, one inlet for CO2 span, and one inlet for H2O span
Connections 0.25-in Swagelok
Mass Flow Sensor 0 to 1.0 standard liters per minute (SLPM)
Heater 8.0 W (turns on/off at 5°C)
Warm-up Time ~20 min (from -30° to +4°C)
Fan 0.7 W (turns on at 45°C and off at 43°C)

Intake Assembly
Filter 1.0-in diameter, sintered stainless-steel disk filter, 10-micron pore size
Orifice Heater 2 kohm (0.07 W at 12 Vdc)
Mixing Volume 750 mL
Sample Connection 0.25 in. Swagelok
Number of Connections for Heater Cable Entry Seals 3 (1 in, 2 out)
Cable Diameter for Heater Cable Entry Seals 2.8 to 6.6 mm (0.11 to 0.26 in.)
Wire Diameter for Heater Cable Screw Terminals 26 to 12 AWG
Wire Stripping Length for Heater Cable Screw Terminals 5.0 mm (0.2 in.)
Screw Tightening Torque for Heater Cable Screw Terminals 0.4 N•m
Orifice Inside Diameter 0.178 mm (0.007 in.)
Dimensions 31 x 12.5 x 19 cm (12 x 5 x 7.5 in.)
Weight 1.4 kg (3.1 lb)

Downloads

AP200 CR1000 Program v.2.01 (31.3 KB) 12-01-2021

AP200 CR1000(X) Program.

Compatible with the LI-850.

Note: For those with the LI-840 contact Campbell Scientific for compatible code.

View Update History

Device Configuration Utility v.2.31 (47.0 MB) 18-12-2024

A software utility used to download operating systems and set up Campbell Scientific hardware. Also will update PakBus Graph and the Network Planner if they have been installed previously by another Campbell Scientific software package.

Supported Operating Systems:

Windows 11 or 10 (Both 32 and 64 bit)

View Update History

Frequently Asked Questions

Number of FAQs related to AP200: 4

Expand AllCollapse All

  1. Which countries can the molecular sieve be shipped to?

    The molecular sieve is a non-hazardous material that can be shipped to any country.

  2. Why did Campbell Scientific start using molecular sieve? Does it have the same effect as the previously used chemicals?

    The molecular sieve has been demonstrated here by our engineering department to be effective at removing CO2 and H2O from the air sample. The change was made for two reasons:

    1. It was a safer alternative than using the previous chemicals.
    2. Increased shipping regulations for the chemicals limited the number of suppliers. 
  3. Can molecular sieve be used in the future to replace bottles for gas analyzers sold before July 2017?

    The molecular sieve is a direct replacement for the old magnesium perchlorate bottles. The molecular sieve may be used for any Campbell Scientific analyzer that used the old bottles.

  4. To prepare the molecular sieve, how many grams are needed per bottle?

    The bottles of sieve for drop-in replacement contain the pellets and a membrane on top. The membrane is necessary to keep the pellets contained while allowing gas to pass over the zeolite. The bottle has the same footprint as the old magnesium perchlorate bottles. The amount in each bottle is listed on the bottle. The amount of sieve needed for each analyzer is the following:

    • The EC150 needs 22 g (drop-in bottle).
    • The IRGASON® needs 22 g (drop-in bottle).
    • The EC155 needs 22 g (drop-in bottle).
    • The AP200 needs 500 g (refill).
    • The 27423 needs 1000 g (refill).
    • The 31022 needs 500 g (refill).
Visit the FAQ Library

Articles and Press Releases