Overview
The UT30 is a durable instrument tower that can be used for a variety of applications. The UT30 tower provides a sturdy mount for many meteorological monitoring applications—especially air quality stations and regional Mesonets, where the 10 m (32.81 ft) measurement height for wind sensors is standard. It also holds antennas, solar panels, environmental enclosures, radiation shields, and crossarms. It is a versatile instrument mount: many of the same sensor mounts that are used with either our tripods or other towers can be used with the UT30.
Read MoreBenefits and Features
- Sturdy, long-term instrument mount
- Corrosion-resistant
Images
Detailed Description
The UT30 tower includes three 3 m (10 ft) sections, one extendable mast, and two cable tie kits. The extendable mast has a 1.5 m (5 ft) length and a 3.175 cm (1.25 in) outer diameter [swagged to 2.5 cm (1 in) OD].
Top 3 m Section
The top section is constructed from 2.5 cm (1 in) OD aluminum tubing. Its width is 25.7 cm (10.1 in) on a side (center of tubing to center of tubing).
Center 3 m Section
The center section is constructed from 2.5 cm (1 in) OD aluminum tubing. Its width is 33.3 cm (13.1 in) on a side (center of tubing to center of tubing).
Bottom 3 m Section
The bottom section is constructed from 3.175 cm (1.25 in) OD aluminum tubing. Its width is 43.2 cm (17 in) on a side (center of tubing to center of tubing).
Mounting Base, Grounding Kit, and Guying Kit
This tower requires a mounting base and grounding kit. Campbell Scientific also recommends guying the UT30 with our UTGUY Guy Kit. See Ordering Info on the web page for more information.
Specifications
| Material | Hardened drawn 6063-T832 aluminum |
| Guyed Tower Area Requirements | ~5 m (17 ft) radius |
| Required Concrete Pad Dimensions |
91 x 91 x 122 cm (36 x 36 x 48 in.) for B18 Concrete Mounting Base Concrete pad requirements assume heavy soil; light, shifting, or sandy soils require a larger concrete pad. |
| Extendable Mast |
|
| Pipe Outer Diameter |
|
| Crossarm Measurement Height | 10 m (33 ft) |
| Height | 10.1 m (33 ft) |
| Shipping Dimensions | 310 x 46 x 46 cm (122 x 18 x 18 in.) |
| Shipping Weight | 29 kg (65 lb) |
Maximum Wind Load Recommendation |
|
| B18 Base (unguyed) | 177 km/h (110 mph) |
| RFM18 Base (with UTGUY) | 177 km/h (110 mph) |
| UTBASE (unguyed) | 177 km/h (110 mph) |
| -NOTE- |
Wind load endurance is affected by quality of anchoring and installation; guy wire tension;
soil type; guy angle; and number, type, and location of instruments fastened to the tower. Wind load recommendation assumes proper installation, proper anchoring, adequate soil, and total instrument projected area of less than 0.19 m2 (2 ft2). For the RFM18 base, the wind load recommendation also assumes that the UTGUY’s turnbuckles are preloaded just enough to equalize tension and that the tower is guyed at a 60 degree angle relative to the ground (maximum). |
Compatibility
Please note: The following shows notable compatibility information. It is not a comprehensive list of all compatible products.
Additional Compatibility Information
Enclosure Brackets
The “-TM” mount option for our environmental enclosures is used to attach our enclosures to a UT30 tower. An enclosure ordered with the “-TM” option will be shipped with a three-piece bracket mounted to the top of the enclosure and an identical three-piece bracket mounted to the bottom of the enclosure. This mounting bracket option uses the same three-piece brackets as the "-MM" option, except the pieces are rearranged so that the flanges are on the side of the bracket instead of in the middle. The distance between the centers of each flange needs to be 17”.
Note:
Enclosures with the "-TM" option are shipped configured for the UT10 tower. UT30 customers will need to: (1) remove the bolts attaching the bracket to the enclosure, (2) slide out the flange sections so that the distance between the center of each flange is 17", and (3) reattach the bracket to the enclosure using the original bolts.
Documents
Videos & Tutorials
Frequently Asked Questions
Number of FAQs related to UT30: 1
-
The top section of the tower is made of 1" OD aluminum tubing; in cross-section, the topmost tower section is 10.1 inches on a side (center of tubing to center of tubing).
The middle section of the tower is made of 1" OD aluminum tubing; in cross-section, the middle tower section is 13.1 inches on a side (center of tubing to center of tubing).
The bottom section of the tower is made of 1.25" OD aluminum tubing; in cross-section, the middle tower section is 17 inches on a side (center of tubing to center of tubing).
Casos de estudio
The West Texas Mesonet (WTM) project was initiated by Texas Tech University in 1999 to......read more